Top seller
No results were found for the filter!
High temperature heating mantle WMO-G2H for flasks, round bottom made of glass quartz heat resistant material allows to work with temperature up to 900°C high heating capacity – short heat-up time flexible heating element an even heat transfer and a gentle treatment of the...
from €440.00
Heating mantle WMO-G2, 2 heating zones for flasks, round bottom with volume up to 20 l flexible glass yarn heating element an even heat transfer and a gentle treatment of the glass high quality design made by hand work thermally insulated and earthed sizes from 500 ml with Ø...
from €304.00
Housing heating mantle WMO-LG for 250 ml round... for flasks, round bottom with volume up to 20 l flexible glass yarn heating element an even heat transfer and a gentle treatment of the glassware plastic-coated metal housing characterised by a chemical-resistant metal housing providing...
€279.00
Housing heating mantle WMO-LGER for 250 ml... with built-in controller for stepless power adjustment • for round bottom flasks with a capacity of up to 20 liters • Flexible glass fiber heating element Even heat transfer and gentle treatment of the glass vessels • Plastic-coated...
€314.00
Heating tape HM-HT-BS30 with protective conductor Features: No protection against ingress of water with inner metal protective braiding and glass fibre insulation product dimensions 30 x 5 mm min. bending radius > 15 mm max. heating element temperature
from €112.00
Heating mantle WM/R2H, for 1000 ml round bottom... 2 heating zones, 450W, incl. personal protection switch
€334.00
Housing Heating Cover WMO-LG For 1,000 mL round flask 2 heating zones Built-in power & heating zone switches
€313.00
Heating tape HM-HT-BS30, glasseide-insulated,... Heating tape HM-HT-BS30. This heat-insulated heating tape is used to heat up and compensate for heat losses on short pipes as well as smaller superstructures, preferably in the laboratory and in the pilot plant, where high power...
from €112.00
Temperature controller Temperature controller Electronic laboratory controller HM-RX1001, can be used up to 1200 ° C, depending on the sensor. The plug-in, microprocessor-controlled temperature controller is housed in a stable table housing and is intended for...
from €441.00
Reihenheizgerät WMO mit 4 Plätzen For circular pistons Series heater in a plastic-coated, chemical-resistant housing (H × W × D) 150 × 580 × 290 mm with four heating places. Each heating station is controlled by a separate power controller, 1.5 m mains supply and...
from €1,952.00
Reihenheizgerät WMO-R6 mit 6 Plätzen LabHEAT®-Serial heating units KM-R6 for flasks, round bottom Plastic-coated, chemical-resistant metal housing with six heating positions. Each heating position is seperately controlled. Max. heating element temperature 450°C. 1.5 m power...
from €2,247.00
Carrying ring KM-TR, plastic coated Tragring KM-TR made of plastic-coated metal for fixing the standard heating hoods in tripod assemblies
from €37.00
Heating cable HM-HC-G, glass insulated, without... Heating cable HM-HC-G, glasseide-insulated If concentrated power is to be applied to pipes, test setups, valves or other parts with small dimensions, this heating cable is an ideal and inexpensive solution. A wide range of applications...
from €62.00
Heating tape HM-HT-202, made of silicon, with... Silicone heating tape HM-HT-201. Prefabricated and very flexible heating tape of the highest quality. The heat conductors are enclosed with high-quality silicone rubber, with an additional metal protective braid on the outside. In...
from €140.00
Heating tape HM-HT-201, made of silicone Silicone heating tape HM-HT-201. Prefabricated and very flexible heating tape of the highest quality. The heat conductors are enclosed with high-quality silicone rubber, with an additional metal protective braid on the outside. In...
from €136.00
Tripod HM-DF, plastic coated Tripod HM-DF for heating hoods made of plastic-coated metal to improve the stability of standard heating hoods
from €104.00
LabHEAT® Standard heating hood The standard heating hoods for round bottom flasks are standard equipment in chemical and biotechnological laboratories. for operating temperatures up to 450 ° C flexible glass heater uniform heat transfer and gentle treatment of glass...
from €301.00
Temperature probe HM-TP2, Pt100, up to 500 ° C,... Temperature probe HM-TP2 Pt100 up to 500 ° C male connector V2A, 4 x 50 mm with diode connector suitable for the KM-RX1001, KM-RX1004 and KM-RX5001 with 2 m temperature regulators connecting cable
€92.00
Temperature Sensors KM-TPG: Pt100, up to 250°C,... Temperature Sensors KM-TPG Pt100 up to 250°C in a glass tube, Ø 6 × 400 mm with diode plug suitable for temperature regulator KM-RX1001, KM-RX1004 and KM-RX4001 with permanently connected compensation line
€184.00
Temperature probe HM-TNF, NiCr-Ni, up to 400 °... Temperature sensor HM-TNF, NiCr-Ni up to 400 ° C with diode plug flat sensor 0.4 x 15 x 400 mm suitable for the KMRX1001, KM-RX1004 and KM-RX5001 with 1.5 m temperature regulators connecting cable
€114.00
Temperature probe HM-TNS, NiCr-Ni, up to 1200 °... Temperature probe HM-TNS, NiCr-Ni up to 1200 ° C Incocell-600 probe 1.5 x 300 mm with diode connector suitable for the KM-RX1001, KM-RX1004 and KM-RX5001 with 2 m temperature regulators connecting cable
€114.00
Temperature probe HM-TP2, Pt100, until 500°C,... Temperature probe HM-TP2 Pt100 up to 500 ° C male connector V2A, 4 x 50 mm without diode connector suitable for the KM-RX1001, KM-RX1004 and KM-RX5001 with 2 m temperature regulators connecting cable
€74.00
Temperature probe HM-TPG, Pt100, until 250°C,... Temperature probe HM-TPG Pt100 up to 250 ° C in the glass tube 6 x 400 mm without diode plug suitable for the KM-RX1001, KM-RX1004 and KM-RX5001 with 1.5 m temperature regulators connecting cable
€165.00
Temperature probe HM-TNF, NiCr-Ni, until 400°C,... Temperature sensor HM-TNF, NiCr-Ni up to 400 ° C without diode plug flat sensor 0.4 x 15 x 400 mm suitable for the KM-RX1001, KM-RX1004 and KM-RX5001 with 1.5 m temperature regulators connecting cable
€114.00